* Use zswap instead of swap in zram
This requires a swap file which will get generated automatically on
startup.
* Fix file size and free disk space comparison
* Set zswap factor to 33%
* Set vm.swappiness to 1
Decrease swapping to a minimum. This is also recommended for database
work loads by the MariaDB documentation. In practice it causes the least
amount of writes to disk when under memory pressure, while still making
swap available when needed.
It seems that Raspberry Pi enabled Multi-Gen LRU by default. By my
testing, it performs worse in some situation. Add it by default for all
platforms, but disable it by default for now.
* Add security library libseccomp
Enable libseccomp to activate seccomp support in HAOS. This will compile
systemd and Docker with seccomp support.
Note: Traditionally Supervisor required to disable seccomp. This seems
no longer to be the case with current Supervisor, but it needs further
testing. All containers started by Supervisor get currently started with
seccomp disabled.
* Enable seccomp in the kernel
The fq_codel network scheduler is the de-facto standard nowadays in most
distros. Systemd enables the scheduler by default if available. Make
sure all boards have the necessary kernel module activated.
* RaspberryPi: Update kernel 5.15.61 - 1.20220830
* Add Yellow to the Raspberry Pi kernel update script
* Bump Yellow to kernel 5.15.61 - 1.20220830
Also drop the work around for the LED polarity as the new firmware
has been fixed.
* Explicitly select no kernel module compression
Home Assistant OS uses a compressed rootfs already, no compression for
kernel modules necessary.
* Bump buildroot
* buildroot d7e4c223e5...5468d36a26 (1):
> package/rpi-firmware: bump version to 1.20220830
* Move Bluetooth protocol configuration to hassos.config
Enable a couple of potential useful Bluetooth protocol drivers.
Also enable Bluetooth Network Encapsulation Protocol since the BlueZ
plug-in seems to be enabled.
* Drop OverlayFS configuration not liked by Docker
* Bump buildroot
* buildroot 0397d9c8f0...2ba3394abf (1):
> package/docker-engine: use kernel modules for extra network drivers
* Make IPv6 SIT tunnel driver a kernel module
This is what distributions seem to be doing too.
* Disable real-time scheduling
It seems that Linux' cgroup v2 currenlty does not support RT scheduling.
* Remove Supervisor RT support flag
With CGroups v2 we can no longer support CPU resource allocation for
realtime scheduling.
* Bump OS Agent to 1.3.0 for CGroups v2 support
* Support firewall matching by pkttype
Matching by pkttype is required by the reference OTBR firewall script.
* Add additional Kernel configurations required for OpenThread.
* Enable wext and nl80211 drivers for wpa_supplicant for all devices
* Enable r8188eu module globally and add related firmware to all devices config
Co-authored-by: Stefan Agner <stefan@agner.ch>
* Bump buildroot
* buildroot 73991f0fee...5b5dff3136 (1):
> package/linux-firmware: Add RTL8152/8153/8156 firmware
* Enable Realtek 8152/8153/8156 USB Ethernet adapter support
Enable kernel driver and install firmware for Realtek USB Ethernet
adapter. While at it, also enable some other common USB Ethernet
adapters which don't require firmwares.
CONFIG_BT_HCIBTUSB selects CONFIG_BT_INTEL. That causes CONFIG_BT_INTEL
to be built-in instead of being built as a kernel module.
When the driver is built-in, loading firmware fails during early boot
with the following error message:
[ 1.058941] bluetooth hci0: Direct firmware load for intel/ibt-17-16-1.sfi failed with error -2
Make sure the driver is built as a module which should fix firmware
loading.
The CRDA (Central Regulatory Domain Agent) utility has been used as a
user space helper to load regulatory information for WiFi drivers.
However, since Linux 4.15 the kernel can load the regulatory information
directly from a signed firmware file "regulatory.db".
The regulatory.db file is provided by the WIRELESS_REGDB package, which
has been already installed since its a dependency of CRDA.
Drop CRDA and select WIRELESS_REGDB package explicitly to make sure the
regulatory.db file is present.
The Wireless Extension framework is deprecated, but it seems that the
Wireless Extensions proc API is still popular (/proc/net/wireless).
Enable the minimal set of Wireless Extension to get the proc API.
* add eq3_char_loop package (eQ-3 char loopback kernel module)
* add generic_raw_uart package (low-latency raw UART kernel driver)
* add rpi-rf-mod package
* add device tree overlay support for RPI-RF-MOD/HM-MOD-RPI-PCB on Raspberry Pi
* enable GPIOLIB and GPIO_SYSFS required for RPI-RF-MOD/HM-MOD-RPI-PCB support.
* add basic RPI-RF-MOD/HM-MOD-RPI-PCB support for ASUS Tinker Board
* add device tree overlay support for ASUS Tinker Board and add
haos-config.txt loading support to U-Boot boot script
* Add SocketCAN support
A Controller Area Network (CAN bus) is a robust vehicle bus standard designed to allow microcontrollers and devices to communicate with each other's applications without a host computer. It is a message-based protocol, designed originally for multiplex electrical wiring within automobiles to save on copper, but it can also be used in many other contexts. For each device, the data in a frame is transmitted sequentially but in such a way that if more than one device transmits at the same time, the highest priority device can continue while the others back off. Frames are received by all devices, including by the transmitting device.
* Update also for GS_USB support
There is a port of the candleLight USB to CAN firmware for CANable. The port works very well under Linux using the gs_usb driver. This firmware does not use slcan, so it is not interchangeable with the stock firmware. However, the CANable appears as a CAN interface natively in Linux
With the candlelight firmware, simply plug in the CANable and the device will enumerate as can0. Set the baud rate and bring the interface up with the following command, and you're good to go!
ip link set can0 up type can bitrate 500000
* Update for Peak PCAN-USB Support
* Enable hidraw driver (#1120)
The hidraw driver is required by some IoT devices such as Wyze sense or
Jablotron JA-100. Enable the driver on all platforms by default.
* Update azure-pipelines-release.yml for Azure Pipelines
* Update azure-pipelines-release.yml for Azure Pipelines
* Update azure-pipelines-release.yml for Azure Pipelines
* Fix double LINUX_HEADERS
* Add support for TI USB 3410 or 5052 serial devices (#542)
* Added BT support to device-support.conf file, and removed BT support from kernel.config file
* Removed BT support, as it was moved to device-support.config file
* Added new line at the end of the file
* Changed:
CONFIG_BT_HCIBTUSB from 'm' to 'y'
CONFIG_BT_HCIBTUSB_BCM from 'y' to 'm'
CONFIG_BT_HCIBTUSB_RTL from 'y' to 'm'
* Update device-support.config
Co-authored-by: Pascal Vizeli <pascal.vizeli@syshack.ch>
